Bukobot 3D Printer Forum

News: Added the Bukobot Parts List (BOM) to Wiki at http://bukobot.com/bukobot-parts-list
Welcome, Guest. Please login or register.
Did you miss your activation email?

Show Posts

* Messages | Topics | Attachments

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - RobDur

Pages: [1]
Electronics & Wiring / Re: HELP assembled but multiple problems
« on: March 08, 2014, 12:05:41 AM »
I soldered the wires around on the switch itself and it took care of the problem now everything is working fine, thanks for your help

Electronics & Wiring / Re: HELP assembled but multiple problems
« on: March 07, 2014, 11:37:06 PM »
That took care of the heating and the Axis movement thanks , I changed out the end stop switch with a new one and still having problems with X axis not stopping when it hits the switch any ideas ??

Electronics & Wiring / Re: HELP assembled but multiple problems
« on: March 06, 2014, 12:44:46 AM »
Here is the whole log from repetier after connection:
00:34:06.125 : start
00:34:06.125 : echo: External Reset
00:34:06.125 : Marlin 1.0.0
00:34:06.125 : echo: Last Updated: 2014-01-08 | Author: Deezmaker
00:34:06.125 : Compiled: Jan 26 2014
00:34:06.125 : echo: Free Memory: 4008  PlannerBufferBytes: 1232
00:34:06.125 : echo:Hardcoded Default Settings Loaded
00:34:06.125 : echo:Steps per unit:
00:34:06.125 : echo:  M92 X111.98 Y111.98 Z6400.00 E630.00
00:34:06.125 : echo:Maximum feedrates (mm/s):
00:34:06.125 : echo:  M203 X500.00 Y500.00 Z3.50 E45.00
00:34:06.125 : echo:Maximum Acceleration (mm/s2):
00:34:06.125 : echo:  M201 X800 Y800 Z100 E10000
00:34:06.125 : echo:Acceleration: S=acceleration, T=retract acceleration
00:34:06.125 : echo:  M204 S3000.00 T3000.00
00:34:06.125 : echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s),  Z=maximum Z jerk (mm/s),  E=maximum E jerk (mm/s)
00:34:06.125 : echo:  M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00
00:34:06.125 : echo:Home offset (mm):
00:34:06.125 : echo:  M206 X0.00 Y0.00 Z0.00
00:34:06.125 : echo:PID settings:
00:34:06.125 : echo:   M301 P8.29 I0.37 D45.91
00:34:06.250 : Error:0
00:34:06.250 : : Extruder switched off. MINTEMP triggered !
00:34:07.217 : Error:Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
00:34:09.323 : echo:SD init fail
00:34:09.354 : FIRMWARE_NAME:Marlin V1 FIRMWARE_URL:http://bukobot.com/marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:Bukobot V2.1 EXTRUDER_COUNT:2
00:34:09.947 : FIRMWARE_NAME:Marlin V1 FIRMWARE_URL:http://bukobot.com/marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:Bukobot V2.1 EXTRUDER_COUNT:2

When I send M999 it activates the Y and Z axis barely and then it hits the endstop switch and stops, extruder heater and bed heater still do nothing, the arrows to move 0.1 mm 10 mm 50mm do nothing in any of the axis.

Electronics & Wiring / HELP assembled but multiple problems
« on: March 03, 2014, 02:17:33 AM »
Ok, I'm done with the assembly, wired as per instructions, software and drivers installed printer settings done as per webpage with classic printer and 250000 baud ( repetier, windows 7 32), printer connects  and when I test flight in manual mode X Y Z travel to home hit the endstop and stop, but that's about it the manual jogs positive or negative don't activate anything the software says Idle, the bed wont heat and the extruder heat stays on for three seconds then it shuts off without heating.
The X axis end stop switch doesn't work, It used to be on the Z axis I switched it it it doesn't work on either one.
I tried it on a rasberry pi and pronterface and the same thing it homes ok I cant do antthing else, could it be that the azteeg X 3 board is defective? 

Hardware & Mechanics / Re: Missing hardware
« on: February 18, 2014, 07:05:56 PM »
I just got mine and so far I'm missing the 30 M5 slim nuts , so I'm stuck on the frame assembly , I haven't been able to find these at local hardware stores either

Pages: [1]
BloQcs design by Bloc
SMF 2.0.3 | SMF © 2011, Simple Machines